Buy JET 708597K JSG-96CS 9-Inch/6-Inch 3/4 Horsepower Belt/Disc Sander, 115-Volt 1 PhaseJET 708597K JSG-96CS 9-Inch/6-Inch 3/4 Horsepower Belt/Disc Sander, 115-Volt 1 Phase Product Description:
- Combination 6-inch belt sander and 9-inch disc sander
- Angle-capable work tables and miter-gauge slots
- Convenient 4-inch dust port serves both belt and disc
- Heavy duty one-piece steel stand
- Two-year manufacturers warranty
Product Description
The unique JET Combination Belt/Disc Sander combines a 9in. disc and 6in. x 48in. belt for workshop versatility. While small and compact, the combo sander offers industrial 3/4 HP power while taking up a small footprint in your shop. A quick-release belt tension lever makes belt changes fast and easy while a quick-lock dust cover allows fast disc changes. Style: Benchtop oscillating spindle sander, Speed (RPM): 1,725, Motor Voltage: 115, Motor Phase(s): Single, Amps: 3, OPM: 30, Belt Size (in. x in.): 6 x 48, Disc Diameter (in.): 9, HP: 3/4
Customer Reviews
Most helpful customer reviews
22 of 22 people found the following review helpful.
GOOD MACHINE..HAD TO RETURN IT
By KRASSEL
Don't get me wrong here, this is a real good machine. Very heavily built, excellant finish, and very quiet. The dust collection is great, it has plenty of power and tracks well. But I had to return it and replace it with the Shop Fox G4790(see separate review). There were a couple of reasons for this. First you cannot remove the end piece from the belt sander and sand on the radius. This piece is an intregal part of the tracking system and must remain on the machine when sanding. I need a machine that I can sand/shape large radius on. Second..I need a machine that I can quickly change belts, as I will go thru 4-5 differant grits in a 10 minute period. Changing the belt on this machine involves removing parts...too slow. The last item was the casters...they should be heavier duty. If I had kept the machine I would have changed them out for Gizzly 3" locking casters.If none of these are important to your use, I would recommend this sander. It's a nice machine and I wish I could have kept it.
22 of 23 people found the following review helpful.
Great Sander - Great Value
By A Customer
I bought this sander from Tool Crib a few months ago. It wasn't on the Amazon.com site at the time.
I went with the open stand because I wanted some storage below. Not sure if that's an option thru Amazon.com.
The sander was easy to set up. The fit and finish was excellent. It runs smooth, though the graphite platen behind the belt sander it somewhat noisy. It seems to have quieted a bit with more use. Bits of the graphite material get all over the place for about the first 15 mins of use but that seems to have taken care of itself.
I found the belt a little tough to adjust as to maintain a given lateral position on the rollers. This is my first belt sander so that might just be due my lack of familiararity with the machine.
The sander has ample power. I have yet to get it to bog down on pine, maple or white oak. The tables are very good. The disk table is machined cast iron and well built. The belt table seems to be pressed from heavy sheet metal but has worked fine for me. It's not flimsy at all. It was fairly easy to square everything up and set the stops. Though on the belt table, I had to leave a little extra gap between the belt and the table because when you tighten the table locks, it seems to pull the table toward the belt. Not a big deal though.
Dust collection is better than I expected. There are sliding panels in the rear of the sander to direct the collection from either the disk or belt sander area. I thought this was good idea. I have a 1-1/2 HP Delta dust collector located about 15 feet from the sander and the combination seems to do a good job at keeping the sanding dust down.
Other than the preceeding minor issues, I think this is a great sander. The value is hard to beat, if not impossible to beat. I find that the sander is very stable on the open stand. It gives me extra storage with a shop-made plywood shelf and saved me a few bucks. Though the closed stand does look nice I though function was more important.
I recommend this sander highly.
11 of 11 people found the following review helpful.Jet 708597K Combination 9" Disc / 6" x 48" Belt Sander
By R. Stevens
Purchased in February 2004 to replace a smaller sander that wore out after 15 years. I was impressed with the quality of the machine. Tracking was easily set up and has stayed true. Plenty of power, smooth operation and the vaccuum system is helpful in dust removal. Only negative was in the foot lever to lock the wheels which bent if I engaged the lock with a foot. Worked fine if one used a hand to set the lock. This flimsey locking mechanism should be improved.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
